Black Month Our biggest deal of the year is coming. VIPs get it first. Join the VIP list, it’s free
Training at Home7 min read

"How to Clean and Care for Your Dance Pole"

By the POLEPLACE team Updated 16 Nov 2026
Close-up of two hands gripping the pole

10% off at Lupit Pole

We train on Lupit Pole. With the code POLEPLACE10 you get 10% off in the Lupit shop.

See Lupit Pole

Clean your dance pole before and after every session with a soft cloth and a cleaner your manufacturer approves for your finish, then wipe it dry. Avoid glass cleaners, oils and harsh household products, check the pole’s tension before you train and re-tighten it only as your manual describes. When the pole comes down, store it clean, dry and with all its parts together.

Short answer: the safest care routine is the one in your pole’s manual. If you are still choosing a pole, our buying guide and our pick, a Lupit home pole, are good places to start.

Why does cleaning your pole matter?

Your grip depends on the pole surface. Every session leaves a thin layer of sweat, skin oil and grip product behind. Over time that film makes the pole slippery, even if your hands are perfectly dry. A clean pole gives you more reliable grip, which means more confidence and safer training. It is also simply more pleasant, especially if more than one person uses the pole at home.

Grip aids deserve a special mention. They help your hands, but they also leave traces on the pole. Tacky products build up faster than drying ones, and when residues from different products mix, the pole can feel dull and unpredictable. Which grip aid suits you is covered in our home equipment guide.

Woman seated by home pole in a home setting
Your living room is enough.

How do you clean a pole before and after training?

The routine takes about two minutes:

  1. Dry wipe first. Go over the whole pole with a clean, soft cloth to remove dust and loose residue.
  2. Clean with an approved product. Put the cleaner on the cloth rather than spraying the room, and wipe the pole from top to bottom. X-Pole’s help centre recommends spraying onto the cloth.
  3. Dry and polish. Finish with a dry cotton or microfibre cloth so no moisture or streaks are left behind.

X-Pole recommends cleaning before and after every use, and suggests a new soft cloth or paper towel. Use a stable step or ladder for the top part, never climb the pole to clean it.

Before training you remove dust and anything left from the last session, so you start with a clean surface. After training you remove sweat and grip product before it dries on. If you used a tacky grip aid, the after-session wipe is the important one.

Which cleaner for which pole finish?

Each finish reacts differently, and manufacturers do not all give the same advice. Here is what two of them say. Always check your own manual first.

Finish What the manufacturer says Source
Chrome and stainless steel Lupit: cotton cloth with pure alcohol or water (or the solvent Nitro diluent 900), then wipe with a dry cotton or microfibre cloth. Lupit FAQ
Powder-coated Lupit: only pure alcohol or water, then wipe dry. X-Pole: no chemical-based cleaners, and its own X-Clean is not for powder coat. Lupit FAQ, X-Pole manual
Brass Lupit: needs frequent cleaning and polishing to stay shiny. Some dancers like the natural oxide layer for grip. X-Pole: X-Clean is not for brass. Lupit FAQ, X-Pole manual
Silicone X-Pole: X-Clean is not for silicone poles. For cleaning a silicone pole, follow the instructions of its manufacturer. X-Pole manual

You can read more about the finishes and how they feel in our article on pole diameter and finish.

What should you not use on a dance pole?

Some products do more harm than good:

  • Glass cleaners. Lupit warns against them, especially those with ammonium hydroxide.
  • Harsh chemicals on powder coat. X-Pole states not to use chemical-based cleaners on powder-coated poles.
  • Bleach and disinfectants. X-Pole’s help centre advises against bleach, disinfectant and sterilising agents.
  • Oils, lotions and anything greasy. They transfer to the pole and make it slippery. X-Pole calls oil and lotion before pole use dangerous.
  • Abrasive sponges or scouring pads. They can scratch the surface.

Notice that the advice differs between brands. Lupit lists water as an option for chrome and stainless steel, while X-Pole’s help centre advises against water for its poles and recommends methylated spirits on a microfibre cloth. [check: whether the X-Pole help centre advice applies to all regions] That is exactly why your own manual is the rule that counts. X-Pole also points out that all cleaning products wear the material over time, so gentle and regular beats aggressive and rare.

Woman viewing pole training on tv in a home setting
Press play and train along at home.

When and how should you re-tighten your pole?

Cleaning keeps the surface safe, checking keeps the whole pole safe. A pressure pole can lose tension over time. Make a quick check part of every session:

  • Grab the pole and push and pull it in different directions. It should not move at the top or bottom.
  • Check the joints between sections. X-Pole notes that joints need tightening regularly and should be checked each time before using the pole.
  • During longer sessions, check again. X-Pole recommends ideally every 30 minutes, and not using the pole until it is re-tightened if anything moves.
  • If the sections of a Lupit Classic G2 turn at the joints in static mode, Lupit says the pole needs to be tightened slightly.

Re-tighten only the way your manual shows, and do not overtighten. Too much pressure can damage the pole or the ceiling, and Lupit notes that an overtightened pole can also spin poorly. The full checklist for before each session is in our guide on how to set up a pole.

Maintenance beyond cleaning

Some models need a little extra care:

  • Bearings on spinning poles: Lupit recommends oiling the lower and upper bearings of the Classic every 3 months with daily use, using machine oil or bearing spray grease.
  • Rubber discs: if you set your pole up and take it down often, Lupit recommends cleaning the rubber surfaces of the discs with pure alcohol before every installation, so they grip the floor and ceiling.
  • Moisture: keep steel parts dry. X-Pole’s help centre notes that moisture and sand can cause rust.

How should you store your pole?

If your pole does not stay up all the time:

  • Clean and dry it before you take it down, including the base and the top dome.
  • Store it warm and dry. X-Pole’s manual says to store the pole only in a warm, dry place. Damp basements, garden sheds and cold garages are not ideal.
  • Protect the surface. Wrap the sections in soft fabric or use a carry case so they do not knock against each other. Powder coat in particular can be damaged if the pole is dropped or scratched.
  • Keep everything together: sections, extensions, tools and the manual in one place, so the next setup is quick.

When should you contact the manufacturer?

Stop using the pole and get in touch with the manufacturer or retailer if you notice a bent section, dents, cracks, a chipped coating, damaged threads or screws, or if the pole will not hold firmly even though you followed the manual. Do not try to fix structural parts yourself.

Woman standing at the pole with one knee lifted
Floor first, then standing, then in the air: every move starts on solid ground.

Your care kit

You do not need much: two soft cloths (cotton or microfibre), a cleaner your manufacturer approves, the tools that came with your pole and, if you have a spinning pole, the lubricant your manual names. Keep them next to the pole, and the routine becomes automatic. For the rest of your setup, see our home equipment guide.

FAQ

How often should I clean my dance pole?

Wipe it before and after every session. X-Pole recommends exactly that, and it keeps sweat, skin oils and grip residue from building up into a slippery film.

What can I use to clean a chrome or stainless steel pole?

Use what your manufacturer approves. Lupit, for example, lists a cotton cloth with pure alcohol or water for chrome and stainless steel, followed by a dry cotton or microfibre cloth.

Can I use glass cleaner on my pole?

No. Lupit specifically warns against glass cleaners, especially those containing ammonium hydroxide. Household cleaners can also leave residue that makes the pole slippery.

Do I need to re-tighten my pole?

Pressure poles can lose tension over time, so check yours before every session and re-tighten whenever it moves, exactly as your manual describes. Do not overtighten.

How should I store my pole when I take it down?

Clean and dry it, keep all parts and tools together and store it in a warm, dry place, as X-Pole recommends. Protect the surface from knocks and scratches, especially if it is powder-coated.

What next?

A clean, well-checked pole is the best start to every session. Now fill it with something fun: the 12-Week Starter Course takes you from your first floor moves to your first spins, and you can try it 7 days for free. If you are about to buy a pole, our buying guide helps, and POLEPLACE10 gives you 10% off at Lupit.

What next?

Start with Class 1 of our 12-Week Starter Course. Every move is taught with our Floor-Stand-Air Method™: on the floor first, then standing, then in the air.

10% off at Lupit Pole with code POLEPLACE10